CH2M Temporary - Tech II - Instrumentation Level 3 - Prudhoe Bay, Alaska in Prudhoe Bay, Alaska
This is a temporary project position expected to last approximately four to six months.
The Instrument Technician supports the Electrical and Instrumentation Team by installing, maintaining, calibrating and adjusting instrumentation and instrument loop components, such as pipe, fittings, tubing, valves and instruments.
Essential Job Functions:
Calibrates, tests, troubleshoots, and repairs various devices and control loops (pneumatic, hydraulic and electronic analog and digital devices involving the pneumatic, hydraulic and electronic analog and temperature and flow of devices fluids found within the petroleum industry)
Troubleshoots and maintains relay logic systems, PLCs, turbine controls, compressor surge flow totalizing loops, air drying systems, local and remote annunciators, gas/oil fired heaters and re-boilers, and valves of varying designs and manufacturers
Works with tubing and piping fittings from vacuum to high pressures to exceed 5,000 psi, and electrical circuits with potentials up to 50 volts
Uses various types of test equipment
Reads, uses and updates electrical, electronic, piping and instrument drawings and schematics
Provides written and oral documentation of job status
Routinely performs safety and productivity observations; shop, field and vehicle inspections; and is required to attend various components of technical, developmental and safety training
Must demonstrate support for the company’s environmental management system
Ability to interpret instrumentation drawings & schematics – Stick in JD
Ability to work at facilities independently without direct supervision
Ability to do instrumentation work on both projects & maintenance
Knowledge, Skills, Ability:
Ability to calibrate, test, troubleshoot and repair various devices and control loops as described in Essential Job Functions section, above
Ability to troubleshoot and maintain systems and equipment as described in Essential Job Functions section, above
Ability to work with tubing and piping fittings from vacuum to high pressures to exceed 5000 psi and electrical circuits with potentials up to 50 volts
Ability to read, use and update electrical, electronic, piping and instrument drawings and schematics
Must be able to work cooperatively with others and alternate
Must be a self-starter, be able to work independently with minimal supervision, and have the ability to use sound judgment in making decisions
Ability to interpret instrumentation drawings and schematics
Knowledge of various facilities across the field
Ability to do instrumentation work on both projects and maintenance
Physical Demand/Work Environment:The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the essential functions of this job, the employee is required to:
Must have ability to stand, walk on level, uneven and slippery surfaces, sit, squat, kneel, reach through low and high ranges and exhibit normal balance and coordination. These basic physical requirements are essential for safe performance of the job in harsh environments with exposure to very cold temperatures and while wearing arctic gear.
Lift 40 lbs from floor to waist level x 2 with a 12 second interval
Lift 40 lbs from floor to shoulder level x 2 with a 12 second interval
Carry: Carry 40 lbs with two hands for 50 feet x 2; self-paced; allow a 60 second rest break after the first carry test
Stair Climb and Carry Test: While carrying 35 lbs with one hand and using the other hand to hold onto a railing, climb up and down 15 steps x 6 for a total of 90 steps; self-paced; allow a rest break after climbing up and down each set of 30 steps
Climb slanted ladder, 7 rungs x 3 for a total of 21 rungs, self-paced and continuous
Repetitive Kneeling Test: Perform from standing, kneel on one knee, alternate from left to right knee, x 5 each knee
Repetitive Stoop Test: Perform from standing position, bend forward at waist as far as possible without bending the knees with hands reaching toward the floor x 5, self-paced, but continuous
Repetitive Squat Test: Perform a functional squat and stand x 5 Twist and Flex Test: Perform from standing alternate toe touches x 5 to each side to assess ability to twist and flex the trunk repetitively
The minimum qualifications for this position are:
Four to five (4-5) years of Instrumentation & Controls experience in an oil field, petrochemical or industrial setting OR an Associate of Applied Science Degree in Instrumentation required WITH two to three (2-3) years of related oilfield experience or education.
Must complete NFPA70E within six (6) months of hire
High School diploma or equivalent GED
Valid driver’s license and ability to be covered by CH2M’s auto insurer
The ideal candidate will possess the following skills and experience:
- Four to five (4-5) years experience in instrumentation and controls and an Associates of Applied Science in Instrumentation
CH2M will not sponsor a work visa (e.g. H1B, etc.,) to fill this position.
CH2M is an Equal Opportunity Employer - M/F/Veteran/Disability. Learn more about your rights under Federal EEO laws and supplemental language.